300B Amp – Page 2 – Bartola® Valves

300B SE Amp: 46 Driver (Part I)

And time arrived to start experimenting with the different drivers. Why? Well, the whole point of the latest modular design is that I can easily (I hope) make quick changes and experiment.

The D3a driver board can be replaced with a new one. In fact I will be building a pair of stacked boards (which are in essence ground planes) to hold the SUT as well as a pentode screen bias regulator and the driver board.

First incarnation will be on the 46 DHT. However, drilled the board to fit either loctal (e.g. 4P1L, C3g, etc.) as well as noval for other 9-pin drivers I have in mind.

The build process is fast. I have the ground plane PCBs, which I drill (M3) to fit multiple plastic hex standoff to hold either PCBs or different turret/2mm connectors to plug in/out the board as needed. This LEGO-like approach is amazing, very happy with the flexibility and speed of work I can get with this.

Stay tuned.

300b driver experiments

01a preamp

300B Amp in action

I’ve been enjoying and carefully listening my new 300B amplifier. I have to say that I love every bit of its sound, treble detail and strong bass. The amplifier is fast and can drive very well my speakers. I only discovered that due to my low level DAC, the gain of the D3a in triode is yet not enough to get it to maximum power. So, I hooked in my beloved 01a preamp. The overall gain is too much of course so had to place the volume control at the output of the 01a stage.

I think a gain of about 130-140 should be ok. Perhaps if I get around in adding the 6SF5 stage then it may be good enough.

So this got me thinking. Of course I have on my list 2 driver tests:

Continue reading “300b driver experiments”

300B SE Amplifier Finished!

When everything was going to plan…

This build became one of the quickest and eventually the most painful from all, perhaps not really. However, it was very challenging in the end. I will tell you why in more detail. Yet, it has been a fantastic learning experience.

Continue reading “300B SE Amplifier Finished!”

300B SE Amp: build part IX (Layout)

Feedback was that more pictures were preferred. So here they are. I have little time, but slowly I will make progress I hope. The main chopping board is what is left now. Layout is tricky as have not enough space given the size of the OPTs 😀

Checking if the EML300B will fit in the cabinet

layout, I will have to drill a lot of M3 holes for the mounting hex standoffs!

300B SE Amp: build part VIII (Cap Boards)

I made a set of useful PCBs. They are intended to mount large (big really big) film capacitors: WIMA DC Link ones!

WIMA DC Link mounting boards + PIO cap board

I use the cost-effective 45μF/600V (MF Part No. DCP4I054507ID2KYSD) in many of my boards as the last capacitor in the filtering network. This is a 2 pin device, however when you go larger like the 80μF/900V (MF Part No. DCP4N058009JD4KYSD), this one has 4 pins and bigger size. The PCB for the later can also accommodate the smaller DC Link of 45μF/600V. The boards have turret or 2mm banana plug connections and an INS-1 Nixie indicator with its associated resistor. Finally a bleeder 3-5W resistor can be added.

The smaller board has the size of the Source Follower PCB. It can be mounted below it or can be used independently. Can fit a variety of PIO/Film capacitors for decoupling or for AC interstage coupling.

Speaking about the Source Follower PCB, I made also a new batch of PCBs as run out of the original ones. I made a minor modification and improvement by adding an LED indicator before the top MOSFET drain. This works in the same way as the gyrator Rev08 PCB. Can be used for normal operation or for A2 current source indicator. Also added an extra PIO/Film 100nF decoupling cap to be mounted under the PCB to decouple the high impedance node to the power supply:

SF PCB Rev03: decoupling cap under board

300B SE Amp: build part VII (D3a driver)

It didn’t take long (or at least as long as I thought it would) to finish the driver board. It has a D3a hybrid mu-follower with SiC cathode bias arrangement:

The board is mounted on top of this previous board.

Continue reading “300B SE Amp: build part VII (D3a driver)”

300B SE Amp: build part V (Fixed Bias)

Last year I developed a voltage reference using an HV LED. Unfortunately these devices from OSRAM seem to be discontinued. I managed to buy enough parts for my own use though. What is interesting from these LEDs is that the dynamic resistance is low. About 150Ω with good current, or between 300Ω to 500Ω. Tempco is very low and with such a low dynamic resistance, they are great for creating a voltage reference with a stable CCS:

The LEDs are extremely bright and found that with a 1mA current are dim enough whilst retaining the stability needed. I have a cap multiplier arrangement and the LED array is fed by a stable CCS. Jumpers on the board allow bypassing LEDs and there is also the option to use a trimmer for variable voltage adjustment. Very handy for screen grid supply and phono stages. The reference voltage is extremely quiet with more than 100dB PSR.

Continue reading “300B SE Amp: build part V (Fixed Bias)”

300B SE Amp: build part IV (Board 1 finished)

Wiring job is done. The fixed bias supply delivers from +50V to -300V. It has more voltage capability as am planning to use this same supply for future builds (e.g. 845 SE). The filament supply set to minimise power dissipation on the filament regulators for the 300B. All working fine, so am happy with this board. Filament noise is 0.3mV.

300B SE Amp: build part III (Layout)

Playing with the layout a bit, here is a view of potential layout of the amplifier board. The PCBs for mounting sockets, turrets and switches are very handy. It accelerates the build process and provides full flexibility.

You may not like the open look and feel, but who cares! I love the aesthetics and those OPTs are enormous!

300B SE Amp – here we go

A Brave New World

Surely you’re as tired as I’m with COVID-19. One of the best things I can do to distract my mind is to keep myself away from social media. Every stone you turn, there is COVID or a statement about it. I won’t moan as I have a job for now and a healthy family. Some members of my family were infected but nothing major. I can only say is that the world has change. And so my day to day life looking after the young family whilst working is a real challenge. Starting my fifth week of lockdown, I have to distract somehow my mind at times, otherwise will go mad.

A New Concept

Continue reading “300B SE Amp – here we go”