Tag: bartola source follower PCB

300B SE Amp: build part VIII (Cap Boards)

I made a set of useful PCBs. They are intended to mount large (big really big) film capacitors: WIMA DC Link ones!

WIMA DC Link mounting boards + PIO cap board

I use the cost-effective 45μF/600V (MF Part No. DCP4I054507ID2KYSD) in many of my boards as the last capacitor in the filtering network. This is a 2 pin device, however when you go larger like the 80μF/900V (MF Part No. DCP4N058009JD4KYSD), this one has 4 pins and bigger size. The PCB for the later can also accommodate the smaller DC Link of 45μF/600V. The boards have turret or 2mm banana plug connections and an INS-1 Nixie indicator with its associated resistor. Finally a bleeder 3-5W resistor can be added.

The smaller board has the size of the Source Follower PCB. It can be mounted below it or can be used independently. Can fit a variety of PIO/Film capacitors for decoupling or for AC interstage coupling.

Speaking about the Source Follower PCB, I made also a new batch of PCBs as run out of the original ones. I made a minor modification and improvement by adding an LED indicator before the top MOSFET drain. This works in the same way as the gyrator Rev08 PCB. Can be used for normal operation or for A2 current source indicator. Also added an extra PIO/Film 100nF decoupling cap to be mounted under the PCB to decouple the high impedance node to the power supply:

SF PCB REv03 test
SF PCB Rev03: decoupling cap under board

45 SE Amplifier – revisited

A unique sound

If you have a small room and high-efficiency speakers, then keep reading. If not, you can still enjoy reading about probably the best sounding output valve in my view. The 45. I wrote about it few times and have to say, it’s still one of the best. Better than a 300B but unfortunately can do only 2W. You can use it in Push-Pull and is superb. Have a look at this.

Continue reading “45 SE Amplifier – revisited”

Ba DHT Preamp (Part II)

I’ve been posting not very frequently lately. This is mainly due to lack of time and the level of business travel which reduced to nearly none the time available for DIY audio. 

Nevertheless, the scarce time always pays off. It’s incredible how selective I have to be in order to prioritise which project I should work on. The list is long though. 

Last time I did a quick exercise on the Ba DHT based on the curves I traced and the LTSpice simulation. Well, you always need to build and test in order to check against simulations. The result is, that you may need to adjust and learn from your practical experiences. 

The Ba (like the Aa) are tricky to use. They pick up any electrostatic induced noise. You don’t need even to place your hand close, the mains noise is induced already in its plate. This force you to shield these valves if you want to use them. Am afraid, that is what it is. My friend Rob (DHTRob) warned me, thank you.

The circuit I posted here, had to be readjusted.  Distortion was way too high. The operating point wasn’t good enough. You’d normally get inclined to run the valve as hot as you can, but I was wrong here with this one.

Continue reading “Ba DHT Preamp (Part II)”

Stop that oscillation please!

I’ve been playing for some weeks the marvellous UV-201a stage.  The addition of the source follower brings a new dimension to this stage.  However, I experienced random oscillation on this setup. I knew it was the MOSFET, but I wanted to pin it down. 

I replaced the SiC version with the famous AOT1N60. That cure the issue, but I wanted to find out what was going on, of course blaming my selection of gate stoppers. 

Continue reading “Stop that oscillation please!”

UV-201a DHT Preamp Revisited


I previously implemented a preamp with the UV-201a. These are very old globe valves, somehow fragile and hard to get in good shape. Despite all this, it’s a superb valve. I have managed to acquire a decent set of them to pair the best valves to use in my preamp.

Recently I developed a prototype PCB for the source follower circuit. The source follower is ideal to place at the output of this preamp due to its low driving current. My 4P1L PSE amplifier will be pleased with more current to pump the Miller capacitance effectively. 

Continue reading “UV-201a DHT Preamp Revisited”