cx-112a DHT preamp

Introduction

This was one of my first DHT preamps. I found a quartet of NOS CX-112a Cunningham (globe) back in Buenos Aires many years ago and built one of my first DHT preamps. I loved it. I played with it before I moved into the 26 and then started the long exploratory journey with DHTs.

The CX-112a can be easily fit in an existing 01a preamp. Take a look at what Thomas Mayer recently blogged about this valve, worth reading it.

Well, you can get more current drive than 01a (nearly double) but no thoriated tungsten filaments. Anyhow, the gain is slightly higher but is very easy to adapt to my gyrator-based circuit, that I couldn’t resist to take the quartet out of my valve stash and make them sing again after so many years.

Continue reading “cx-112a DHT preamp”

VT-25 DHT Preamplifer

VT-25 in action

Now I’m back from our long trip, I found some time to play with the “Mule“. I wanted to revisit my old VT-25 preamplifier. Many years ago I had my first VT-25/10 preamplifier which was based on a gyrator load. Then it morphed to a transformer coupled (LL1660/40mA) version to drive my TVC before I settled into the 4P1L for some long time.

The circuit design

The VT-25 has always been on my list of favourite DHTs. It’s gone ridiculously expensive these days and is hard to get. I have a couple of pairs in very good shape luckily.

Continue reading “VT-25 DHT Preamplifer”

Gyrator PCB board updated (Rev06)

After some further testing and prototyping, I’ve updated the gyrator board PCB to provide additional protection to the lower FET device with:

Protection Zener (D3) between drain and source (through-hole)
Back to back protection Zeners (D1 and D2) between gate and source to ensure positive gate bias for higher currents on jFETs and use of enhancement MOSFET

Layout was carefully adapted to ensure track separation due to HV in place. Result is that the new gyrator board provides all protection needed on the lower device and simplifies the build process

Here is an example of a completed board tested:

01a Preamp Gen2: Build Complete

Yesterday I started with the build of a new 01a preamp Gen2. I made some component changes during the build process thanks to Andy Evans who reminded me of the Russian FT-2 teflon capacitors. I had a pair left of 220nF FT-3 caps in stock!

The circuit is the same as the original preamp but with some component changes:

C1 is 100nF/630V ClarityCap polypropylene
MOSFET is DN2540 and jFET is BF862
Rmu is 330Ω Kiwame
Filament resistors are NOS Russian wirewound 51Ω/20W. I use a pair of them in parallel. Bias is about 5V.
Filament bias using Rod Coleman v7 regulators. Set starved to 200mA
The output caps are Russian NOS teflon FT-3 220nF / 600V. You can use a pair of FT-2 100nF alternatively.

The bias point is changed slightly up to 5V so the anode voltage is increased to 115V to get the 3mA of anode current. This time I’m using the BF862 which can be soldered in the gyrator PCB instead of the 2SK170. I preferred the sound and higher bandwidth as well as lower output impedance. The BF862 is a real winner as lower FET.

Here is a view of the preamp inside:

The heavy FT-3 caps are mounted on top of the gyrator PCB boards. The top anodised plate is 4mm thick and anodised. The teflon UX-4 sockets from Luciano Bandozzi (Jakeband) are mounted with silent blocks and Rod’s regulators are bolted to the top plate. you don’t have to as they dissipate very little power in this case.

How does it sound? Well, just played it for a couple of hours and I’m amazed with the subtle differences that the Russian wirewound resistors and output cap + BF862 can bring to this preamp. We did some listening tests recently with Andy Evans comparing filament resistors and these ones were real winners for both of us.

I hope it improves with time after breaks in a bit more.

4P1L: pump up the current!

Background

I’m a firm believer than sharing knowledge and experience is the best way forward to continue learning yourself. It always pay pack at some point. This time Paul Prinz, a fellow implementer of the 3B7 DHT Preamp using the gyrator PCB, came back with a great suggestion. He found a MOSFET which could do high drain currents, it has high transconductance and most importantly the parasitic capacitances were low even close to the BF862. Hooray, I thought. We may have a great solution here to use the gyrator load for currents above 25mA and with similar performance to the great BF862. There are some other depletion MOSFETs that can do high currents, however they all have relatively high capacitances and low transconductances when VDS is low, like in the cascoded gyrator circuit.

The BSH111BK is an enhancement MOSFET, so doesn’t have a “depletion” behaviour like the jFETs. This isn’t a problem as the bias voltage can be set by the reference CCS.

For comparison, here is a brief summary of the key characteristics of these three devices:

	BF862	BSH111BK	MMBFJ310L
Ptot (W)	0.3	0.3	0.225
VDSmax (V)	20	55	25
VGS off (V)	-1.2		-4
IDSS (mA)	25	210	60
Gfs (mS)	45	640	18
Ciss (pF)	10	19.1	5
Crss (pF)	1.9	1.5	2.5
Coss (pF)		2.7

Continue reading “4P1L: pump up the current!”

3B7 DHT Preamplifier

An enthusiast blog reader (Paul Prinz) implemented a nice version of the DHT preamplifier using the gyrator PCB but for the 3B7 triode. The 3B7 triode has a pair of DHT triodes on the same bottle. It has a high mu for a DHT (about 20) but with that it comes the higher anode resistance. This was a drawback when implementing a choke or transformer loaded stage due to the high anode resistance (there is no free lunch am afraid). However, with the mu-stage, this doesn’t become an issue and we can get the most out of this valve using the gyrator load.

Although I tried the 3B7 in the past, I proceeded to get it out from my valve stash and trace it again. Here is a nice set of a Sylvania military NOS one:

Continue reading “3B7 DHT Preamplifier”

CX-301a DHT Pre-amp Build from Malaysia

A fantastic build of the 01a preamp using the gyrator PCB from Cheah:

I have just completed my 01a preamp with STP3NK60ZFP output follower. The preamp sounded great !!

A great looking preamp using Rod Coleman’s regulators, output follower and V-Cap capacitors. The jFET is BF862.

Well done Cheah!

Building gyrator boards

I’ve been on some business travel so haven’t had much time to work on stuff, however I did get a set of gyrator boards for a friend and a customer:

BF862 configured for 4P1L preamp
2SK170 configured for 01a preamp

4P1L preamp with BF862 gyrator

Many have asked me about this preamp with gyrator load. Here is the latest implementation which I preferred most in terms of sound. The mu resistor is 470Ω which is a nice compromise between BF862 transconductance and distortion. I adjusted it on test. I use a 100nF for C1 so R6 is 10MΩ. R4 can be either 300KΩ, 330KΩ or even 390KΩ. Difference would be only on the voltage range for the CCS. I found running it at 25mA to be perfectly fine, some BF862 can even do J310. I prefer this SMD compared to the J310. It performs much better even at high frequency:

Abusing the Gyrator Load

On my previous post, I covered my initial build work on the gyrator test mule using the gyrator PCB. I did all the lovely soldering work (which I do enjoy not like milling or drilling) and proceeded to do several tests.

Some interesting observations based on my abuse of the gyrator which yielded on several MOSFETs and JFET damaged as a result:

CCS reference: I used an external multi turn 5KΩ potentiometer via lead cables. I wired it incorrectly and that contributed to one of the initial faults. Be sure you look carefully on this if you use an external pot. if you use the on-board trimpot, this is not an issue.
JFET: this is the interesting one. If you want to run the lower JFET at very low biasing current for a larger jFET (e.g. J310) you will find that the JFET needs to operate close to cut-off voltage (somewhere between -2 and -6V). This VGS required will definitely forward bias the Zener protection diode D1 and prevent from reaching lower bias current (I found it about 10mA for J310). To resolve this you just need to add a back to back zener as shown below. This isn’t a problem for an BF862 or a 2SK170 as their cut-off voltages are quite small.
Failure: if you abuse the FETs, they will die. And if they die you will get a nice short across them and you will measure nearly HT at the mu output. Just replace the MOSFET and JFET (probably both are damaged)

Continue reading “Abusing the Gyrator Load”

LCR Phono: design notes (Part III)

My previous design wasn’t good for two reasons:

Input capacitance was too high due to Miller effect.
Overall gain wasn’t enough: 55dB was marginal as 60dB would be ideal for an MC stage. Obviously this doesn’t apply to an MM cartridge where 40dB should be more than ok.

Continue reading “LCR Phono: design notes (Part III)”