DHT Audio Shootout @ London

Here’s the summary of the shootout day we had yesterday at my place with Tony Rees and Andy Evans

Test Music

For testing the pre-amps Andy suggested the following 2 tracks:

Ravel Feria (Cleveland/Boulez)
Janacek The Cunning Little Vixen Act 3 Scene 7 “A vixen’s running through the woods” Prague Theatre/Gregor

The Ravel is orchestrated for a large orchestra and percussion, and listening was particularly for the timbre of strings, brass and woodwind and the clarity of the percussion. The Janacek is for several different voices and chorus, and listening was for the tone and character of the voices and how well they were differentiated from each other. In both cases the overall clarity, life and crispness was considered.
Andy Evans

Although I wasn’t familiarised enough with these 2 tracks myself, I found them to be an excellent choice and a reflection of Andy’s musical experience and knowledge as musician.

UV-201a final version – finished!

After doing all the soldering part (which I enjoy much), the preamp is now finished. It sounds as good as the original breadboard:

For the curious ones, here you have a picture of the inside:

The teflon sockets are bolted straight into the 4mm top aluminium plate. No microphonic noise this way. Rod Coleman V7 regulators set to 200mA. A pair of Russian Military NOS wire-wound resistors in parallel provides the filament bias. The gyrator PCB is set as per original circuit and each valve at 3mA. These are DC coupled to the MOSFET follower PCB set at 10mA each. The output is then taken out from a pair of FT-3 teflon caps.

Now to enjoy this beauty!

UV-201a DHT Preamp Revisited

I previously implemented a preamp with the UV-201a. These are very old globe valves, somehow fragile and hard to get in good shape. Despite all this, it’s a superb valve. I have managed to acquire a decent set of them to pair the best valves to use in my preamp.

Recently I developed a prototype PCB for the source follower circuit. The source follower is ideal to place at the output of this preamp due to its low driving current. My 4P1L PSE amplifier will be pleased with more current to pump the Miller capacitance effectively.

Continue reading “UV-201a DHT Preamp Revisited”

UV-201a preamp test

First listening test with these beauties, it sounds really nice!

And here is the look inside for the curious ones who always ask me to provide more details about the construction. Here is a good ground wiring example. The preamp is dead quiet:

01a Preamp Build: UV-201a version – step 2

Adding filament bias and output caps

01a Preamp Build: UV-201a version – step 1

This is what I managed to do with a couple of hours at the workshop. Time is gold for me these days. Quick drilling and fitting the main components. You can’t get a smaller preamp than this one. It’s quite packed:

Planning the layout before drilling

Back panel with all connectors (supply and signal)

Inside the preamp

Close look at the gyrator boards

UV4 sockets with rubber dampers

Fitting a pair of brass base UV201a

Next, soldering. Yay, just looking forward to my favourite part of the build process

01a Preamp Build: UV-201a version – layout

Just playing with the layout a bit. The gyrator boards, the UV4 sockets and the Rod Coleman regulators. All in a tiny aluminium box:

Building gyrator boards

I’ve been on some business travel so haven’t had much time to work on stuff, however I did get a set of gyrator boards for a friend and a customer:

BF862 configured for 4P1L preamp
2SK170 configured for 01a preamp

4P1L preamp with BF862 gyrator

Many have asked me about this preamp with gyrator load. Here is the latest implementation which I preferred most in terms of sound. The mu resistor is 470Ω which is a nice compromise between BF862 transconductance and distortion. I adjusted it on test. I use a 100nF for C1 so R6 is 10MΩ. R4 can be either 300KΩ, 330KΩ or even 390KΩ. Difference would be only on the voltage range for the CCS. I found running it at 25mA to be perfectly fine, some BF862 can even do J310. I prefer this SMD compared to the J310. It performs much better even at high frequency: